1000 Lumen 10 Watt Super Bright, Cool White LED Module


1000 Lumen 10 Watt Super Bright, Cool White LED Module
Stock Number: 31325 OP
 Review Average:  
 Number of Reviews: 5
 View ReviewsReview this item
$2.95


Availibilty: In Stock   Units: 190
Quantity 



SHARE
    
     Email this to a friend     

Detailed Description

REQUIRES CURRENT LIMITING & MOUNTING TO HEATSINK WITH THERMAL PAD: Case Temp. <45C max.
Super Bright Cool White LED.
Lumens: 1000min
Color Temperature: 6000-6500
Max Reverse Voltage: 5V
View angle: 160deg.
Forward Voltage Drop: 9-11VDC
Forward Current: 1000mA Max
ALUMINUM BASE SURFACE MOUNT PACKAGE
Sq: 20mm H: 3.5mm WT: .011

View PDF Data Sheet


California Proposition 65 Warning WARNING: This product can expose you to chemicals including Chromium which is known to the State of California to cause cancer and which is known to the State of California to cause birth defects and/or other reproductive harm. For more information, go to www.P65Warnings.ca.gov



 Product ReviewsClick here to review this item
Replaced my Microscope Light Source With One of These 7/4/2019
I have an old USSR era microscope that has great optics, but a sickly 12v halogen light source. You have to use a blue filter to get the light anywhere near natural color and the intensity is poor for the amount of glass the light has to go through to get to my eye. So I used this 10 watt LED and the inexpensive, 10 watt LED driver to switch out light sources. My main concern was heat. Halogens dont care about the heat but LEDs certainly do. The Bulb enclosure was a pretty roomy aluminum box. I was able to cut and grind down an old CPU heat sink to fit snugly, fins facing down, and drilled vent holes in the sides of the box to increase airflow. I soldered up the chip and attached it to the heatsink with some screws through the mounting holes of the chip into the tapped holes I drilled in the heatsink. I used thermal grease designed for CPU chips, so Im hoping it has enough throughput for the heat from this thing. Im not an engineer, so I was just giving as much cooling I could think of and hope it is enough. The whole contraption works really well. The light is blinding I can control that with a diaphragm that is built into the microscope stage and the color is correct without any filters. The only problem I encountered was that I soldered the power wires through the holes in the attachment points for better physical strength and they protrude just enough to short out the power through the heatsink. Easy fix though by slightly bending the tabs up to avoid the heatsink. I guess these were designed for surface mounting. Anyway, at full bore, I measure the heat on the outside of the enclosure at 114~120 F. Pretty hot, but the light didnt dim or trip its thermal protection feature. Actually cooler than the halogen, so that is good for looking at live specimens on the microscope stage. I might add a small muffin fan to the outside of the enclosure to increase the airflow over the heatsink fins just to increase the lifespan of the chip. Really proud of how well this worked out...most of my projects do not come to a nearly as satisfying conclusion as this one!
- Daniel Goodale-Porter, VA
 
Beware limiting current 4/11/2017
Beware that these will not drive 10W LEDs at full power for more than about 20 seconds cold. LED current increases as die temperature climbs, and eventually the short circuit protection of the drivers kick in to turn them off. I made an amazingly bright light bar with individual 10W driver modules 31557PS, but it only stays lit for about 20 seconds for the reasons described.
OK
 
Awesome LED module 11/14/2016
I bought ten of these modules, wired three in series & connected to the 30 watt AC power supply / DC converter designed to drive LED modules. I then installed the three modules equally spaced apart on a 1X 1 x 32 square stock aluminum tube. I then installed them into a 2 X 4 fluorescent fixture. after removing three burned out 32watt T8 bulbs These LED modules out perform the fluorescent tubes hands down. I was so impressed, I converted the other two fixtures. I still cant believe that I have only a total of 30 watts of LED providing more bright white light than 96 watts of fluorescent light from one fixture. Truely Amazing. Will definitely be ordering more of these!!
- William, CT
 
Fabulous, Fabulous, Fabulous 5/10/2016
For those who have used these LEDs you know I dont need to say more. For those who have not, I will expand my review. I have used these LED units on two devices I made for myself. The first was a bike light second to none. I see bike lights selling for 350$. I built one using this LED for about 20 bucks and some machining. It destroys the competition. Now after all these years of having to stare into other peoples high beams I am capable of some photonic wrath of my own. I wish I could show the video of this bike light in action. The other device I made was a yard flood light. Every one sells LED yard spot lights but not flood lights. And those spot lights are over priced and under engineered. You should ask yourself how can you possibly sink and radiate 20 watts of LED power inside of a plastic enclosure with no external heat sink. And ask yourself why do those same commercial manufacturers claim a 50,000 hour LED life but provide only a 1 year warranty. The most hours there can be in any one year is 8784. And half of those hours for most of us are daylight. I measured 1160 lumens at the LED surface with my general lux meter. A word of warning though. You should heed the specs closely for the time and temp limits regarding anode/cathode tolerance. I made a fixture for soldering mine that sinks the connections and keeps them at a common ground state. OVERHEATING WILL REDUCE LIGHT OUTPUT! For my floodlight I used 18 of these LEDs switchable in banks of three. The design of my flood makes it possible to send light left, right, or forward. With over 20,000 lumens total output it is a yard light worthy of the name YARD LIGHT. I added a visor to the flood to keep it from offending my neighbors or low flying aircraft.
- Jim F., MN
 
My fav leds. 3/18/2016
This is my favorite of all the LEDs ive tried. Amazing light output in a small package, very nice easy solder pads, very low cost. I use 10w dropping resistors for pulsed units and for continuous duty, the #31557-PS drivers. Great experiences so far, with both.
- Alan, KS
 



View below for the rest of the Email Specials.
Triggered Time Delay Relay - Delay on Make - 12VDC
Triggered Time Delay Relay - Delay on Make - 12VDC
Item #: 37672 RL
$4.95
Retriggerable - Delay on Make Timing Relay - 12VDC
Retriggerable - Delay on Make Timing Relay - 12VDC
Item #: 37673 RL
$4.95
Pack of 8 -  2ea 2,3,4 & 5 Position Lever Action Wire Splice
Pack of 8 - 2ea 2,3,4 & 5 Position Lever Action Wire Splice
Item #: 37770 TM
$2.50
LM2596 Step Down Adjustable 1.5-37V DC/DC Converter
LM2596 Step Down Adjustable 1.5-37V DC/DC Converter
Item #: 30148 PS
$3.95 
sale $2.95 
Remote Controled Relay,  Wireless 4 Channel - 12V
Remote Controled Relay, Wireless 4 Channel - 12V
Item #: 36825 MI
$14.95 
sale $12.95 
Mini Panel Meter, Dual LED Display 30 Volts & 10 Amps DC
Mini Panel Meter, Dual LED Display 30 Volts & 10 Amps DC
Item #: 30303 ME
$10.95
3 Digit Incrementing Electronic Counter
3 Digit Incrementing Electronic Counter
Item #: 37659 MI
$4.95
Ceramic Blade Tuning Screwdriver - 2.6mm Flat Blade.
Ceramic Blade Tuning Screwdriver - 2.6mm Flat Blade.
Item #: 37600 TL
$1.95
4-11/16
4-11/16" Sq 1-1/4" 12VDC BLOWER
Item #: 37557 FN
$10.95
1000 Lumen 10 Watt Super Bright, Cool White LED Module
1000 Lumen 10 Watt Super Bright, Cool White LED Module
Item #: 31325 OP
$2.95
Pack of 25 - 1x40 Pin - 0.1
Pack of 25 - 1x40 Pin - 0.1" Pitch Headers - 5 Colors
Item #: 37725 HC
$2.95
12 VDC 4 Channel Adjustable Sequential Controller
12 VDC 4 Channel Adjustable Sequential Controller
Item #: 37716 RL
$19.95
0-100VDC 4 Digit Red LED Panel Meter 3 Lead Snap-in
0-100VDC 4 Digit Red LED Panel Meter 3 Lead Snap-in
Item #: 37706 ME
$4.95
0-100VDC 4 Digit Red LED Panel Meter 3 Lead
0-100VDC 4 Digit Red LED Panel Meter 3 Lead
Item #: 37711 ME
$3.95
3 digit LED DC Voltmeter With Dual USB 5V Charging Ports
3 digit LED DC Voltmeter With Dual USB 5V Charging Ports
Item #: 37536 ME
$6.95
12VDC 1
12VDC 1" (25mm) X 9/32" (7mm) Box Fan
Item #: 37553 FN
$2.95
Microwave / Radar Motion Sensor Module, 5V
Microwave / Radar Motion Sensor Module, 5V
Item #: 36114 MP
$7.95
Sheet of 64 - Polyurethane Bumpers (Feet) - 5mm x 10mm Diameter
Sheet of 64 - Polyurethane Bumpers (Feet) - 5mm x 10mm Diameter
Item #: 37202 HD
$2.95
6-7/16
6-7/16" X 4-11/16" X 2-11/16" Plastic Instrument Case
Item #: 37289 BX
$6.95
Automotive Relay 5 Terminal Pigtail Socket
Automotive Relay 5 Terminal Pigtail Socket
Item #: 33948 RL
$1.89
Pack of 530 - Heat Shrink Tubing - 5 Colors - 8 Sizes
Pack of 530 - Heat Shrink Tubing - 5 Colors - 8 Sizes
Item #: 36930 HS
$6.95
Pack of 7 - 2.54mm (0.1
Pack of 7 - 2.54mm (0.1") Pitch PCB Terminal Blocks
Item #: 36882 TS
$4.95
Pack of 5 - DIN Rail Terminal Strip - Gray - Bussable
Pack of 5 - DIN Rail Terminal Strip - Gray - Bussable
Item #: 37439 TS
$3.95
Pack of 5 - 5.08mm Mating Connectors 7, 8, 9, 10 & 12 Position
Pack of 5 - 5.08mm Mating Connectors 7, 8, 9, 10 & 12 Position
Item #: 37409 PL
$5.95
660pc. Type 0805 Chip Resistors - 33 Values - 1 ohm to 680K
660pc. Type 0805 Chip Resistors - 33 Values - 1 ohm to 680K
Item #: 37375 RS
$5.95
Pair Mini Chassis Slides
Pair Mini Chassis Slides
Item #: 36610 HD
$2.95
12VDC, 500 RPM Gearhead Motor
12VDC, 500 RPM Gearhead Motor
Item #: 35500 MD
$12.95
Digital Multimeter 4 Digit True RMS
Digital Multimeter 4 Digit True RMS
Item #: 35999 TE
$19.95
12 Volt DC Plug Power Supply, 2.5A, Netgear
12 Volt DC Plug Power Supply, 2.5A, Netgear
Item #: 33380 PS
$6.95
24VDC Relay, DPDT 25A Tyco
24VDC Relay, DPDT 25A Tyco
Item #: 31236 RL
$7.95
SPST On-Off Toggle Switch, Screw terminals
SPST On-Off Toggle Switch, Screw terminals
Item #: 33240 SW
$1.95
8VDC, 11000 RPM Motor
8VDC, 11000 RPM Motor
Item #: 36903 MD
$5.95
Mini Panel Meter, 2 Wire - Snap-in - 3 Digit Red, 30VDC
Mini Panel Meter, 2 Wire - Snap-in - 3 Digit Red, 30VDC
Item #: 33065 ME
$5.95
24VDC, 1-5/8in. Square X 1-1/8in. Sanyo Box Fan
24VDC, 1-5/8in. Square X 1-1/8in. Sanyo Box Fan
Item #: 32790 FN
$3.95
Pack of 5 - 16mm PCB Spacer / Connectors 1x40 Pin  - 0.1
Pack of 5 - 16mm PCB Spacer / Connectors 1x40 Pin - 0.1" Pitch
Item #: 37729 HC
$2.25
 

You May Also Like