|
|
 |
Home > Motors > Stepper Motors
Stepper Motors
 |
|
|
Product:
3.6V, 1.8 DEG VEXTA STEP MOTOR
|
|
MFG: ORIENTAL MOTOR
P/N VEXTA PK266-02A
COIL: 3.6V/2A/1.8ohms/2.5mH
TYPE: 2Phase Unipolar, 6 lead
STEP ANGLE: 1.8deg.
127oz/in holding torque, 1/4" X 3/4" flatted steel shaft. 4 corner bolt holes. 12" leads. Can be connected as Bi-Polar.
L: 2-3/16" (Body) SQ: 2-3/16" WT: 1.6
Data Sheet
|
|
|
|
|
Product:
1.8 DEG. 3V STEPMOTOR
|
|
MFG: SHINANO KENSHI
P/N: STP-58D4002-03
COIL: 3VDC/.42ohms
TYPE: 2 Phase Bi-Polar 4 lead
STEP ANGLE:1.8 deg
7mm dia. X 18mm steel shaft with a pressfit 1-1/2” dia. 36 tooth, sintered steel cog belt gear. Ball bearings, 3" leads, 4 corner mounting holes threaded M4.5, Removable steel mtg. bracket
L: 2-5/8"(Body) SQ: 2-3/16" WT: 2.2
|
|
|
|
|
Product:
1.8 DEG. STEPMOTOR
|
|
MFG: ASTROSYN
P/N: 23KM-K213-P7V
COIL: 3VDC/1.8 ohms/2.6mH
TYPE: 2 Phase Uni-Polar, 6 lead
STEP ANGLE: 1.8 deg
1/4" Dia. X 1" steel shaft with press fit steel COG belt pully. Four corner mounting holes. 4" leads.
L: 1-3/4" ( Body) SQ: 2-3/16" WT: 1.1
|
|
|
|
|
Product:
5V MINI LINEAR STEP MOTOR
|
|
MFG: HAYDON
P/N: 20841-05-028
TYPE: 2 PHASE BI-POLAR 4 lead
COIL RATING: 5VDC/18ohm/5.5mH/.27A
MAX RATE: 400PPS
LINEAR STEP: .001in.
Linear actuator/step motor with rotating, 9/64" (.140") Dia. X 2-5/8" steel shaft. 1-1/4" max travel.1-3/64" (1.031") mounting ctrs. 20" leads. Shaft end thread: 2-56 UNC 2A X .15" long
L: 3-1/2" O/A W: 1-5/16" O/A WT: .06
Data Sheet
|
|
|
|
|
Product:
1.8Deg. SANYO STEP MOTOR
|
|
MFG: SANYO DENKI
P/N: 103H7121-0415
COIL: 2A/1.25 ohm/1.9mH
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg 120step/rev
6mm dia. X2 4mm serrated steel front shaft with plastic 16 tooth X 1/2" dia. worm gear (removable). 6mm X 10mm smooth back shaft. removable 3/8" thick steel/rubber shock mounting plate with 4 corner mounting holes. 3" leads.
L: 2" (Body) SQ: 2-3/16” WT: 1.2
|
|
|
|
|
Product:
1.8Deg. SANYO STEP MOTOR
|
|
MFG: SANYO DENKI
P/N: 103G770-1856
COIL: 3.5V/1.5A/2.4ohm/2.9mH
TYPE: 2 Phase Bi-Polar 6 lead
STEP ANGLE: 1.8 deg
6.5mm dia. X 18mm steel shaft with a pressfit 3/4” dia. 25 tooth, plastic cog belt gear. Ball bearings, 5in leads. Removable anti-vibration bracket with mtg. ears. 4 corner mounting holes (motor).
L: 2-1/8"(Body) Sq: 2-3/16" WT: 1.3
Limited time only, while supplies last and subject to change at any time.
|
|
|
|
|
Product:
1.8Deg. MINEBEA STEP MOTOR
|
|
MFG: MINEBEA
P/N: 23KM-K102-P1V
COIL: 3A/1ohm/2.2mH
TYPE: 2 Phase Bi-Polar 4 lead
STEP ANGLE: 1.8 deg
8mm dia. X 18mm steel shaft with a pressfit 13/16” dia. 18 tooth, aluminum cog belt gear. Ball bearings, 6pin connector Mating cable supplied, 4 corner mounting holes threaded M4.5.
L: 2-5/8"(Body) SQ: 2-3/16" WT: 1.9
|
|
|
|
|
Product:
1.8Deg. 3V STEP MOTOR
|
|
MFG: SHINANO KENSHI
P/N: STP42D4009
COIL: 3V/1.6 ohm
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg step/rev
5mm dia. X 24mm steel shaft with plasticl 21 tooth X 3/4" dia. cog belt pully. 4 corner m3x0.5 mounting holes. 5" leads.
L: 1-5/8" (Body) SQ: 1-9/16” WT: .64
|
|
|
|
|
Product:
3.3V STEP MOTOR ASSEMBLY
|
|
MFG: JAPAN SERVO
P/N: KP-56LM2G-001
COIL: 3.3VDC/2.2A
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg Motor
.1deg. Output Shaft(18/1 ratio)
Step motor, gear box assembly with brake. Apply 24VDC to release brake (removable). Motor side 13/32"dia. X 9/16" steel shaft with coupling (held by roll pin), 6" leads, Removable steel mtg. bracket.
L: 4-1/2"(Body) W: 3-1/2" H: 4-1/4" WT: 2.6
|
|
|
|
|
Product:
3V/ 1.8Deg. SHINANO STEP MOTOR
|
|
MFG: SHINANO KENSHI
P/N: STP-58D4002-02
COIL: 3VDC/.42ohms
TYPE: 2 Phase Bi-Polar 4 lead
STEP ANGLE: 1.8 deg
7mm dia. X 18mm steel shaft with a pressfit 13/16” dia. 18 tooth, sintered steel cog belt gear. Ball bearings, 3" leads, 4 corner mounting holes threaded M4.5
L: 2-5/8"(Body) SQ: 2-3/16" WT: 2
|
|
|
|
|
Product:
24V LINEAR STEP MOTOR
|
|
MFG: EASTERN AIR DEVICES
P/N: LB11ABM-4R
COIL: 24VDC/.96A/25ohms
TYPE: 4 Phase Uni-Polar 5 lead
STEP ANGLE:15 deg(motor)
Removed from equipment linear step motor. 1/8" dia. X 3/8" rear shaft. 4-56UNS-3A threaded X 1-5/8" long steel front shaft, 4 mounting holes threaded 4-40. 12" leads.
L: 1-7/8"Body Dia: 1-1/16" WT: .3
|
|
|
|
|
Product:
24V 1.8 deg. SANYO DENKI STEP MOTOR
|
|
MFG: SANYO DENKI
P/N: 103-771-18
COIL: 24V/.18A
TYPE: Uni-Polar 5 lead
STEP ANGLE: 1.8 deg
Used motor with a 1/4" dia. X 3/4" steel shaft. 4 corner mounting holes . 7" leads.
SQ: 2-3/16" L: 2" WT: 1.2
|
|
|
|
|
Product:
12V USED LINEAR STEP MOTOR
|
|
MFG: SHINKOH
P/N: 23PB-H031
COIL: 12VDC/.25A
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE: 7.5 deg(motor) approx. .01in/step,1/2"/rev.
USED linear step motor. .25" dia. X 3-3/16" shaft. 1-7/8" long sprial "groove" cut into shaft for a travler (not supplied). 2 mtg. tabs for clamping. 3" leads.
L: 1-1/8"Body Dia: 2-1/2" WT: .65
|
|
|
|
|
Product:
1.8Deg. STEPMOTOR DRIVE
|
|
MFG: SHINANO KENSHI
P/N: STP-57D505
COIL: 5.3VDC/1A
TYPE: 2 Phase Uni-Polar 5 lead
STEP ANGLE:1.8 deg (Motor)
Assembly#: 127K18074
Step motor & gear assembly for copy machine. Motor has 7mm steel shaft with a pressed on aluminum spur gear. Removable gear unit contains 5 various plastic gears, 2 have mechanical unidirectional clutch. 5in. leads.
Motor L: 3" Sq.: 2-1/4" WT: 2.3
Assembly L: 4-3/4" W: 5-1/4" H: 2-7/8" WT: 2.9
|
|
|
|
|
Product:
1.8Deg. 2.88V STEP MOTOR
|
|
MFG: SHINANO KENSHI
P/N: STH-56D309
COIL: 2.88VDC/2.4A
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg (Motor)
Assembly#: 127K80020
6.5mm dia. X 22mm steel shaft with a rollpinned 3/4” dia. 22 tooth, plastic cog belt gear. Ball bearings, 5in leads. Removable anti-vibration bracket with mtg. ears. 4 corner mounting holes (motor).
L: 2-1/4"(Body) SQ: 2-3/16" WT: 1.5
|
|
|
|
|
Product:
WIDE RANGE STEPMOTOR DRIVER CW250
|
|
P/N: CW250
INPUT: 20-60VDC
OUTPUT: Selectable up to 5A max.
STEP ANGLE: 1.8 deg:200steps/Rev.
Microstep: 1/8: 1600 steps/Rev.
Full bridge driver for hybrid stepmotors.
Switch Selectable output current.
Over temp & Output miswire Protected.
Opto isolated Step pulse input (Clock input +5V Level).
Opto Isolated Direction input ( +5V Level)
Terminal strips in/out.
L: 5-3/4" W: 3-3/4" H: 1-3/4" WT: 1.5
Data Sheet
|
|
|
|
|
Product:
7.8V/2A/1.8 Deg. SIZE 85 STEPMOTOR
|
|
P/N: 85BYGH450C-01
COIL: 7.8VDC/3.9Ohms/24mH
TYPE: 4 Phase Uni-Polar 8 lead
STEP ANGLE: 1.8 deg
New, heavy duty step motor, 63Kg./cm holding torque. 13mm (.55") X 35mm (1-3/8") steel shaft. 4 corner mtg. holes. 24" leads.
Compatable Driver: Order 17452-MS
L: 6" Body Sq: 3-3/8" WT: 11.2
Data Sheet
|
|
|
|
|
Product:
6.2V/1A/1.8 Deg. SIZE 57 STEPMOTOR
|
|
P/N: 57BYGH213
COIL: 6.2VDC/6.2Ohms/10mH
TYPE: 4 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg
New step motor, 9000g.cm holding torque. 6.35mm (.25") X 19mm (.75") steel shaft. 4 corner mtg. holes. 24" leads.
Compatable Driver: Order 17452-MS
L: 2-3/8" Body Sq: 2-3/16" WT: 1.6
Data Sheet
|
|
|
|
|
Product:
24V/.34A/1.8 Deg. SIZE 57 STEPMOTOR
|
|
P/N: 57BYGH006
COIL: 24VDC/71 Ohms/90mH
TYPE: 4 Phase Uni-Polar 6 lead
STEP ANGLE: 1.8 deg
New step motor, 4400g.cm holding torque. 6.35mm (.25") X 19mm (.75") steel shaft. 4 corner mtg. holes. 24" leads.
Compatable Driver: Order 17452-MS
L: 1-5/8" Body Sq: 2-3/16" WT: 1
Data Sheet
|
|
|
|
|
|
|
|
|
|
